.:HSTuners::

12-11-2002, 01:20 PM

does anybody know if there is a hole in the fire wall to run wires to the battery? if not i have to drill.

nonovurbizniz · 12-11-2002, 01:34 PM

there are existing holes but they're usually filled with rubber grommets made to fit both the hole and the exact number of wires that already go through it.

If you do drill make sure you prime the bare metal after you drill and use a rubber grommet to stop water from leaking in your pass. compartment.

*ChrisCantSkate* · 12-11-2002, 01:36 PM

ive always found holes to use... just godda look

12-11-2002, 01:41 PM

the hole for the wiring harness is pretty big

ebpda9 · 12-11-2002, 02:23 PM

i know i had to punch that rubber in the harness to hook my brother's system to his integra. and when i had to run wires inside mine i removed and drilled the palate for the clutch ( cause i have an auto)

*pdiggitydogg* · 12-11-2002, 02:39 PM

i poke holes in that rubber grommet. the rubber usually seals back over the wire i put through. if not then i put some silicon on it and seal it back again.

12-12-2002, 02:59 PM

on your car there is a hole on the drivers side under where the clutch fluid would go. Its big enough to run 1/0 awg wire through. I had to do this. It comes out about 3" above the kick panel.

blind34_1 · 12-12-2002, 05:16 PM

often times there is a rubber cap you just pop out. In mine, its almost like they expect you to put a system in your car. look closely.

12-11-2002, 01:20 PM	#1
alpine3069 Posts: n/a	firewall? does anybody know if there is a hole in the fire wall to run wires to the battery? if not i have to drill.

12-11-2002, 01:34 PM	#2
nonovurbizniz Registered User Join Date: Jul 2002 Location: ECUSA Age: 46 Posts: 2,693	there are existing holes but they're usually filled with rubber grommets made to fit both the hole and the exact number of wires that already go through it. If you do drill make sure you prime the bare metal after you drill and use a rubber grommet to stop water from leaking in your pass. compartment. __________________ I am an A$$hole... take anything I say to heart at YOUR OWN RISK...

12-11-2002, 01:36 PM	#3
ChrisCantSkate Thought Police Join Date: Aug 2001 Location: orlando florida Age: 40 Posts: 9,662	ive always found holes to use... just godda look __________________ Black Vtec Prelude-h22a power'd Many dreams come true, and some have silver linings. I live for my dreams and a pocket full of gold.

12-11-2002, 02:23 PM	#5
ebpda9 Repost Wagon Join Date: Dec 2001 Location: over here Age: 43 Posts: 17,266	i know i had to punch that rubber in the harness to hook my brother's system to his integra. and when i had to run wires inside mine i removed and drilled the palate for the clutch ( cause i have an auto) __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-11-2002, 01:41 PM	#4
iRACEmyCTR Posts: n/a	the hole for the wiring harness is pretty big

12-11-2002, 02:39 PM	#6
pdiggitydogg Yahoo Watashi wa kattaze! Join Date: May 2002 Location: Meanwhile, up in The D... Age: 40 Posts: 10,579	i poke holes in that rubber grommet. the rubber usually seals back over the wire i put through. if not then i put some silicon on it and seal it back again.

12-12-2002, 02:59 PM	#7
1badcivic Posts: n/a	on your car there is a hole on the drivers side under where the clutch fluid would go. Its big enough to run 1/0 awg wire through. I had to do this. It comes out about 3" above the kick panel.

12-12-2002, 05:16 PM	#8
blind34_1 Registered User Join Date: May 2002 Location: IL Age: 39 Posts: 1,813	often times there is a rubber cap you just pop out. In mine, its almost like they expect you to put a system in your car. look closely.