...and the rebuild commences...

[thermal]

SPECS:
-JDM B18c-R
-AEBS sleeved 84mm bored, honed, and decked
-Wiseco 84mm ceramic coated pistons
-Manley/Full Race rods
-ACL bearings
-Stock JDM ITR head milled 20 thousandths to target compression 9.1:1
-Spoon cam gears
-AEBS head studs
-Cometic head gasket
-Spearco/Turbonetics half size dual core aluminum radiator
-Slim fan 14 inch 1200 CFM radiator fan

Turbo Stuff:
-Garrett GT35R .82 a/r S-cover watercooled
-LoveFab SST turbo manifold. Last batch made by Cody Loveland
-Tuner Toys oil feed/return line
-Tial race BOV
-Tial 44mm WG
-Precision 750hp Intercooler
-GReddy oil filter block adapter
-Thermal R&D 3 inch exhaust system (no cat-converter)
-DMH 3 inch flow tech exhaust cut-out
-JG/Edelbrock intake manifold
-CRYO2 intercooler spray (filled with N2O... I will never use CO2)
-Hondata intake manifold heat shield (gasket)
-Mustang 75mm throttle body and TPS recalibrated via AEM EMS
-Ford IACV recalibrated via AEM EMS
-Custom 3 inch downpipe by me, V-band ordered
-Custom dump tube by me
-Custom catch-can by me

Elecetronics/gauges:
-GReddy 60mm electronic peak/hold A/F ratio gauge
-GReddy 60mm electronic peak/hold EGT gauge
-GReddy 60mm oil temperature gauge
-GReddy 60mm mechanical boost pressure gague
-GReddy 52mm electronic fuel pressure gauge
-GReddy 52mm electronic oil pressure gauge
-GReddy turbo timer
-GM boost solenoid
-AEM UEGO wideband

Fuel Management:
-AEM EMS
-Precision 1000cc peak/hold fuel injectors
-Boostfed racing adjustable fuel pressure regulator
-Fast Turbo steel braided fuel lines
-Golden Eagle fuel rail (1st gen)
-Custom liquid filled fuel pressure gauge
-Walbro 255LPH intank fuel pump (high pressure)
-AEM Twin-Fire ignition (AEM C2di and MSD Pro billet dizzy with ICM/BlasterSC... back-up)
-AEM 5 BAR MAP sensor
-Honda CBR coil-on-plug conversion

Transmission:
-B16 tranny
-Del Sol shifter
-Quaife LSD
-Gear Speed synchro
-Exedy Twin disk

Suspension/Braking:
-Omni-POWER USA fully adjustable strut/spring
-Omni-POWER USA adjustable camber kit
-Omni-POWER USA 2nd gen lower control arm
-JIC magic front and rear strut bar
-Steel braided brake lines
-AEM brake pads
-Volks/Rays Racing TE37 Gunmetal +42mm offset 16x7
-Rota Slipstream flat black (winter tires)
-Yokohama Parada Spec-2 205/45 front tires
-Nitto 455 205/40 rear tires
-Polyurethane inserts
-ARP extended wheel studs
-Kyogen lug nuts... will switch to maybe some Skunk2 extended)
-Crossdrilled/Slotted front and rear brake rotors
-JK motorsports Traction Bar

Interior/Exterior/Misc:
-Mugen front lip
-GReddy shift knob
-Full Black interior conversion from Tan, done by me
*00 GSR dash
*97 ITR rear seats
*95 LS rear panels
*94 GSR seat belts
*01 ITR carpet
*Recaro SRD with OEM sliders and self fabricated bracket
*Non-SRS JDM ITR steering wheel
*USDM ITR floor mats
*JDM ITR shift boot
*Repainted center console and arm rest
*Some stereo stuff