.:HSTuners::


::Hondas Wanted::
 

Go Back   HSTuners > Honda / Acura Cars > Civic/Del Sol
User Name
Password
FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
Old 10-19-2005, 10:02 PM   #1
redneckwithaford
Parked
 
Join Date: Oct 2005
Location: Calgary AB
Age: 43
Posts: 17
No Clue

So I started doing some clean up on the engine that I had aquired (for free).

I then discovered that the guy who gave it to me really didn't know anything about engines.


Turn out that it wasn't out of a 92 Si but and HF.

The motor and manual tranny are a D15Z1.

So now the dilemal starts.

The tranny is for fuel milage not performance.

My car right now has an auto.

The engine currently in my car is a D16A6.

So do I start from scratch looking at junk yards or do I use what I have??

The plan was a solid 240 Hp at the flywheel with use of turbo and just under 300 Hp with nitrous.

So niether trannys are good and I'm just not to shure on the engines. Can't find alot of info on the D15 and haven't spent a lot of time looking at the D16

Any Ideas??? I would like to use what I have due to cost but I understand if that is not going to reach my goals.

Steve
redneckwithaford is offline   Reply With Quote
Old 10-19-2005, 10:13 PM   #2
AzCivic
Moderator
 
AzCivic's Avatar
 
Join Date: Feb 2002
Location: Az
Age: 42
Posts: 3,804
the d16a6 is really a good engine to start w/ but yeah you need a decent tranny. I'd suggest a 96-00 Civic Ex tranny, you can usually find them for $150 or so.
AzCivic is offline   Reply With Quote
Old 10-19-2005, 10:15 PM   #3
redneckwithaford
Parked
 
Join Date: Oct 2005
Location: Calgary AB
Age: 43
Posts: 17
Will that tranny fit my 90?

Should I Upgrade the head or just mod what I have?

Steve
redneckwithaford is offline   Reply With Quote
Old 10-19-2005, 10:20 PM   #4
AzCivic
Moderator
 
AzCivic's Avatar
 
Join Date: Feb 2002
Location: Az
Age: 42
Posts: 3,804
yeah it'll fit.

if you wanna boost i'd just put in some aftermarket pistons/rods. and then worry about the turbo kit and proper fuel managment
AzCivic is offline   Reply With Quote
Old 10-19-2005, 10:28 PM   #5
thermal
Banning Machine
 
thermal's Avatar
 
Join Date: Aug 2001
Location: My Garage, Va.
Posts: 5,547
sad to say that you will still end up dropping some cash to get a decent set-up. I'm not very familiar with those engines, I do know a bit about D16Z or D15b or D16Y. As I said before, the 96-00 D16Y8 trannies are the best D-series trannies. Remember that you are cable right now and will have to switch to hydraulic. There is a lot of work ahead of you. Just be patient and you will eventually get there. Read and read and read tech stuff. Those EF's are light as hell.....
__________________


Project Teg

Visit the Turbo Forum

Last edited by thermal : 10-22-2005 at 01:26 AM.
thermal is offline   Reply With Quote
Old 10-19-2005, 10:54 PM   #6
redneckwithaford
Parked
 
Join Date: Oct 2005
Location: Calgary AB
Age: 43
Posts: 17
Thermal - The car is an auto so have to start from scratch anyways. So I will look into that Tranny.

AzCivic - Would you sugest any head work other than big cams.
Also I would like to have a programable ECU.
Suggestions please??
redneckwithaford is offline   Reply With Quote
Old 10-19-2005, 11:03 PM   #7
AzCivic
Moderator
 
AzCivic's Avatar
 
Join Date: Feb 2002
Location: Az
Age: 42
Posts: 3,804
I say in boosted applications money that could be spent on the head is better spent elsewhere, like the block, tranny, turbo kit, and engine management. my suggestion would be to do nothing to the head except maybe clean up the vavle seats and replace whatever might go bad in it.

my knowledge w/ OBD0 is rather limited, I know there are quite a few free type programs where you just buy what you'd need to burn new chips and the program you'd use to edit things like fuel and ignition maps is a free download. I forget their names though.
AzCivic is offline   Reply With Quote
Old 10-20-2005, 01:29 AM   #8
redneckwithaford
Parked
 
Join Date: Oct 2005
Location: Calgary AB
Age: 43
Posts: 17
Thermal


What casting numbers should I be looking for on the tranny.

Steve
redneckwithaford is offline   Reply With Quote
Old 10-20-2005, 09:31 AM   #9
AzCivic
Moderator
 
AzCivic's Avatar
 
Join Date: Feb 2002
Location: Az
Age: 42
Posts: 3,804
s40 b000
AzCivic is offline   Reply With Quote
Old 10-22-2005, 01:33 AM   #10
thermal
Banning Machine
 
thermal's Avatar
 
Join Date: Aug 2001
Location: My Garage, Va.
Posts: 5,547
^yep
That is very important since people might try fooling you. Non-Y8 trannies have smaller casing too. As far as programmable ECU's, try Uberdata or Chrome. Those programs should be free and OBD-0 compatible. Uberdata is both OBD-0 and OBD-1.
__________________


Project Teg

Visit the Turbo Forum
thermal is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 03:20 AM.


Powered by vBulletin Version 3.5.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
© 2006 HSTuners.com