.:HSTuners::

01-16-2003, 10:36 PM

Who here has put Dynamat in there car? I have opted for the cheaper generic version called FatMat [www.fatmat.com], and got a bulk pack of 100sq ft for $100. Who has installed their own? How hard was it? I am looking to do 4 doors, back deck, all trunk. I was considering the floor and ceiling if I could figure it out. Ideas? Its an '02 Civic sedan.

a96710 · 01-16-2003, 11:13 PM

I have Dynamat....got it for cost where I use to work. 60% off retail (high mark up on that sh*t). It's easy to install. You'll need some kind of roller to flatten the sheets to the surface and a heat gun to warm up the material and the glue.

01-17-2003, 12:13 AM

thezeb.com

is cheap

C's 94 InTeGrA · 01-23-2003, 03:18 PM

I have it.. i did my whole trunk in my Integra for about 90$... since my audio guy gets wholesale.. its really good cause it stopped allthe rattling but now since i put my body kit on the back bumper sounds like shit....

01-24-2003, 06:42 AM

fatmat isnt generic..its exaclty the same as dynamat but since the compant isnt as huge the prices are better.....watch using a heat gun......specially on parts like quarter panels cause you can cause the pain on the outside to bubble and peel off......my suggestion is to go to autozone and get some ubndercoating spray..prolly 2 cans......spray the floor of your trunk with it....and maybe your quarter panels.....then cover everything in fatmat.....use a hair dryer.......and i just used an old paint roller with a plastic tube...some of um come like that and i bought a little plastic roller at lowes for like $0.98

01-24-2003, 10:05 AM

Their instructions dont mention heat. Is it really necessary?

01-28-2003, 10:53 PM

i used dynomat extreme on my trunk lid....it worked wonders....

it didnt say to use a heat source, and the guy told me its made so yyou dont have too, but i used a hair dryer anyways....it just made it that much easier....(its more plyable when warmed up) i did it all my hand, no rollers....looks nice (except for the fact that i must have been stoned,

cuz i put it on upside down from when the trunk lid is open

01-31-2003, 04:06 PM

helped my friend who is a proffesional installer instal it on his car. he got a case i cant remember how much for like 40 bucks. heat roller and alittle time thats all you need. this summer im doin my trunk. cant wait

a96710 · 01-31-2003, 04:38 PM

Quote:

Originally posted by izod
Their instructions dont mention heat. Is it really necessary?

it is cause that's what warms up the glue and helps the material form better.

ifeldwn02 · 02-01-2003, 02:48 AM

i had it in my truck and it worked really good but it is high

i've got a friend that works at an audio store in my town who did his entire cab of his tocoma. u can tap on his door but it kills the sound

01-16-2003, 10:36 PM	#1
izod Posts: n/a	Who Has Dynamat? Who here has put Dynamat in there car? I have opted for the cheaper generic version called FatMat [www.fatmat.com], and got a bulk pack of 100sq ft for $100. Who has installed their own? How hard was it? I am looking to do 4 doors, back deck, all trunk. I was considering the floor and ceiling if I could figure it out. Ideas? Its an '02 Civic sedan.

01-23-2003, 03:18 PM	#4
C's 94 InTeGrA 4th Gear Join Date: Jan 2002 Location: Dover, Ohio Age: 39 Posts: 858	I have it.. i did my whole trunk in my Integra for about 90$... since my audio guy gets wholesale.. its really good cause it stopped allthe rattling but now since i put my body kit on the back bumper sounds like shit.... __________________ 2003 Apex Silver Mitsubishi Evolution 8

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-16-2003, 11:13 PM	#2
a96710 Registered User Join Date: Oct 2002 Location: Vancouver, Wa Age: 43 Posts: 1,454	I have Dynamat....got it for cost where I use to work. 60% off retail (high mark up on that sh*t). It's easy to install. You'll need some kind of roller to flatten the sheets to the surface and a heat gun to warm up the material and the glue.

01-17-2003, 12:13 AM	#3
SofaKingSmooth Posts: n/a	thezeb.com is cheap

01-24-2003, 06:42 AM	#5
sc0rch Posts: n/a	fatmat isnt generic..its exaclty the same as dynamat but since the compant isnt as huge the prices are better.....watch using a heat gun......specially on parts like quarter panels cause you can cause the pain on the outside to bubble and peel off......my suggestion is to go to autozone and get some ubndercoating spray..prolly 2 cans......spray the floor of your trunk with it....and maybe your quarter panels.....then cover everything in fatmat.....use a hair dryer.......and i just used an old paint roller with a plastic tube...some of um come like that and i bought a little plastic roller at lowes for like $0.98

01-24-2003, 10:05 AM	#6
izod Posts: n/a	Their instructions dont mention heat. Is it really necessary?

01-28-2003, 10:53 PM	#7
Azkikr111 Posts: n/a	i used dynomat extreme on my trunk lid....it worked wonders.... it didnt say to use a heat source, and the guy told me its made so yyou dont have too, but i used a hair dryer anyways....it just made it that much easier....(its more plyable when warmed up) i did it all my hand, no rollers....looks nice (except for the fact that i must have been stoned, cuz i put it on upside down from when the trunk lid is open

01-31-2003, 04:06 PM	#8
speedster69 Posts: n/a	helped my friend who is a proffesional installer instal it on his car. he got a case i cant remember how much for like 40 bucks. heat roller and alittle time thats all you need. this summer im doin my trunk. cant wait

02-01-2003, 02:48 AM	#10
ifeldwn02 3rd Gear Join Date: Jan 2003 Location: columbus,ms Age: 40 Posts: 393	i had it in my truck and it worked really good but it is high i've got a friend that works at an audio store in my town who did his entire cab of his tocoma. u can tap on his door but it kills the sound