.:HSTuners::

04-07-2002, 09:31 AM

Whats a decent price for a used B18 out of a GSR? I am planning on that for a summer project for my civic and need to start looking at used engines. I am going to rebuild it for use with a turbo. Any helpful hints?

****Also I am looking for any cheap / free mods i can do on my 97 civic right now to gain a little faster time in the quater mile.

04-08-2002, 12:13 AM

GSR = 3,000 dollars

Free Mods =
Put Ice on Motor
Advance Timing
Strip the Inside Out
Remove A/C
Remove Power Steering
tighten the TB cable

Cheap Mods =
Buy a muffler and have a shop pipe it for you (cost a lil $$)
Home-Made Intake (pcv piping with a filter)
Short Shifter

What position are you going for?
Street Racer? Drag Racer? Show Car?

04-08-2002, 06:18 AM

http://car-part.com/dealersaz.shtml

Try the above link. Goes to many salvage yards all over the USA. I got set of 2001 Civic struts from on of these dealers for $125. I've seen some engines and engine parts listed. You can do a search on all the dealers.

Hope this helps.

slowEJ6 · 04-08-2002, 03:21 PM

pvc pipe under the hood is not ok

just get a K&N drop in filter and be happy.

04-08-2002, 03:28 PM

Ok before I get anymore off the wall suggestions, look at my site and see what i've done so far...

http://members.sounddomain.com/63lowrider

And you guys, Hybrid is right, for a custom intake you have to use ABS piping...i know cause I just made one for my buddy who bought a 2002 dakota last month.

04-09-2002, 01:33 AM

I've seen the piping wrapped in thermal insulation..actually seemed to work..just gotta be careful...its a CHEAP mod...but I mean it will work

04-09-2002, 12:16 PM

ii've heard that pvc pinping can't withstand high temps of heat. might melt of ya even with the thermal wrapping.

04-07-2002, 09:31 AM	#1
Ricin97Civic Posts: n/a	Engine Swap / cheap or free mods Whats a decent price for a used B18 out of a GSR? I am planning on that for a summer project for my civic and need to start looking at used engines. I am going to rebuild it for use with a turbo. Any helpful hints? ****Also I am looking for any cheap / free mods i can do on my 97 civic right now to gain a little faster time in the quater mile.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-08-2002, 12:13 AM	#2
ZeroAccess Posts: n/a	GSR = 3,000 dollars Free Mods = Put Ice on Motor Advance Timing Strip the Inside Out Remove A/C Remove Power Steering tighten the TB cable Cheap Mods = Buy a muffler and have a shop pipe it for you (cost a lil $$) Home-Made Intake (pcv piping with a filter) Short Shifter What position are you going for? Street Racer? Drag Racer? Show Car?

04-08-2002, 06:18 AM	#3
Bartkat Posts: n/a	http://car-part.com/dealersaz.shtml Try the above link. Goes to many salvage yards all over the USA. I got set of 2001 Civic struts from on of these dealers for $125. I've seen some engines and engine parts listed. You can do a search on all the dealers. Hope this helps.

04-08-2002, 03:21 PM	#4
slowEJ6 Registered User Join Date: Nov 2001 Location: Oviedo, FL Age: 42 Posts: 3,195	pvc pipe under the hood is not ok just get a K&N drop in filter and be happy.

04-08-2002, 03:28 PM	#5
Ricin97Civic Posts: n/a	Ok before I get anymore off the wall suggestions, look at my site and see what i've done so far... http://members.sounddomain.com/63lowrider And you guys, Hybrid is right, for a custom intake you have to use ABS piping...i know cause I just made one for my buddy who bought a 2002 dakota last month.

04-09-2002, 01:33 AM	#6
ZeroAccess Posts: n/a	I've seen the piping wrapped in thermal insulation..actually seemed to work..just gotta be careful...its a CHEAP mod...but I mean it will work

04-09-2002, 12:16 PM	#7
nauticapinoy Posts: n/a	ii've heard that pvc pinping can't withstand high temps of heat. might melt of ya even with the thermal wrapping.