.:HSTuners::

03-31-2003, 01:52 PM

alright this is the first time that i have taken the head off of my car, i need to put a new head gasket on it, and well i could really use some help on how others took theirs off, the easiest way would be the best (duh)

but thanks all

03-31-2003, 11:51 PM

good idea would be to pick yourself up a helm's manual

*pdiggitydogg* · 04-01-2003, 07:28 AM

Quote:

Originally posted by 96coupe
good idea would be to pick yourself up a helm's manual

yep, if you dont have some kind of manual for this...you really should...go get one

ShEaNy · 04-01-2003, 11:43 AM

04-01-2003, 01:48 PM

after u get the helms manual, i suggest the following:

take off the intake manifold and leave it on the car

get some assembly lube to reassemble the head (cam/cams)

spray ur head gasket with copper spray (available at ur auto supply store) for better sealing

Good Luck!!

ebpda9 · 04-01-2003, 03:48 PM

it's not that hard but you gotta know what are you doing. make sure you unblot the head in the correct order or you might get warpage. also make sure that the engine wasn't started for the past 6 hour (cool off) or you might warp the head

04-04-2003, 10:07 AM

alright i got a helms manual, but its at a friends house (shit), and my car is un moveable, and as for the sitting for hours, how about 6 days, will that do ^_^, and one question, od i have to take the exhaust manifold off, it looks like i do and i REALLY don't want to do that

04-10-2003, 02:26 PM

well my 1st question is what head are you putting back on the motor? get your self a 96-00 head gasket from honda. much better than the older ones. while you are in there you may want to consider replacing the timing belt and possibly the water pump. one of the more difficult bolts to remove would have to be the lower pulley bolt(17mm) i would try to remove this first because beleive me it sucks to have alot taken off and then you cant get that bolt off!!!

if you are reusing the same head i would just leave the intake manifold on the head. as far as the exhaust manifold goes , im sorry but that has to come off.

i personally have never used a helms manual

let me know how it goes.....i'll do what i can to help

03-31-2003, 01:52 PM	#1
Senshi Posts: n/a	takeing head off alright this is the first time that i have taken the head off of my car, i need to put a new head gasket on it, and well i could really use some help on how others took theirs off, the easiest way would be the best (duh) but thanks all

04-01-2003, 01:48 PM	#5
rhd sir Posts: n/a	takin ur head off after u get the helms manual, i suggest the following: take off the intake manifold and leave it on the car get some assembly lube to reassemble the head (cam/cams) spray ur head gasket with copper spray (available at ur auto supply store) for better sealing Good Luck!!

04-01-2003, 03:48 PM	#6
ebpda9 Repost Wagon Join Date: Dec 2001 Location: over here Age: 43 Posts: 17,266	it's not that hard but you gotta know what are you doing. make sure you unblot the head in the correct order or you might get warpage. also make sure that the engine wasn't started for the past 6 hour (cool off) or you might warp the head __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-31-2003, 11:51 PM	#2
96coupe Posts: n/a	good idea would be to pick yourself up a helm's manual

04-01-2003, 11:43 AM	#4
ShEaNy Registered User Join Date: Apr 2002 Location: Winnipeg, MB Age: 39 Posts: 3,821

04-04-2003, 10:07 AM	#7
Senshi Posts: n/a	alright i got a helms manual, but its at a friends house (shit), and my car is un moveable, and as for the sitting for hours, how about 6 days, will that do ^_^, and one question, od i have to take the exhaust manifold off, it looks like i do and i REALLY don't want to do that

04-10-2003, 02:26 PM	#8
chahonda Posts: n/a	well my 1st question is what head are you putting back on the motor? get your self a 96-00 head gasket from honda. much better than the older ones. while you are in there you may want to consider replacing the timing belt and possibly the water pump. one of the more difficult bolts to remove would have to be the lower pulley bolt(17mm) i would try to remove this first because beleive me it sucks to have alot taken off and then you cant get that bolt off!!! if you are reusing the same head i would just leave the intake manifold on the head. as far as the exhaust manifold goes , im sorry but that has to come off. i personally have never used a helms manual let me know how it goes.....i'll do what i can to help