.:HSTuners::

04-13-2002, 04:17 PM

sorry if there has allready been a post on this topic, d*mned if i could find it. here's the deal....
i'm trying to run wires into my drivers door to hook up an aftermarket alarm system to my power locks (92 LX)
i'm stumped at how to get the door panel off and i don't think i can run the wires unless i do this
i think i'm close but i don't want to break anything

so if anyone has done this and knows how, or knows of a good DIY i'd love it.....

thanks
Sean

slowEJ6 · 04-13-2002, 06:39 PM

unscrew the door handle, unscrew anything from the door armrest, unscrew the speaker, unscrew any screws around the speaker area, look for screws under the door......pry stupid little caps off, yank the panel off. that should do it.

04-13-2002, 06:49 PM

i pretty much figured this is how it was done
i'm just a bit nervous about the prying off of stupid little white caps. i agree that those things suck because i always seem to break them and then they don't go back on very well

oh well..... here's to nothing

*KwikR6* · 04-13-2002, 08:23 PM

If your worried about breaking them then go to a junk yard and take a whole bunch and if you break yours...use your leftovers

*Whtehnda93DXSdn* · 04-14-2002, 11:21 AM

after you remove the screws for the doot handle and the cup portion to hold on to just start at the very bottom and pul out a little and look up to see where the pops are...Oce you do put your hands on each side and pull outwards..that should pop them w/out messing them up.

and if nothing else as stated go to the junkyard and pick up a coupl e extras..

04-14-2002, 03:34 PM

so let's say i break a piece and go to the junkyard to find out that i can't find a replacement.... is there anywhere you can order these, like a dealer or something?
a dealer would probably charge me 20 for them, F***in dealers!

later

*KwikR6* · 04-14-2002, 04:44 PM

Yeah dealers are a rip off...but they do have them at least

04-13-2002, 04:17 PM	#1
seanjuan Posts: n/a	removing door panels on a 5th gen sorry if there has allready been a post on this topic, d*mned if i could find it. here's the deal.... i'm trying to run wires into my drivers door to hook up an aftermarket alarm system to my power locks (92 LX) i'm stumped at how to get the door panel off and i don't think i can run the wires unless i do this i think i'm close but i don't want to break anything so if anyone has done this and knows how, or knows of a good DIY i'd love it..... thanks Sean

04-13-2002, 08:23 PM	#4
KwikR6 Mind Blowing Join Date: Oct 2001 Location: Cloud 69 Age: 44 Posts: 8,871	If your worried about breaking them then go to a junk yard and take a whole bunch and if you break yours...use your leftovers __________________ I JDM. I My Honda The epitome of stupidity is expressed so fluidly with the shity lyric theory you try to spit at me. I CAN'T WAIT FOR SUMMER!!!

04-14-2002, 11:21 AM	#5
Whtehnda93DXSdn It has 4 Doors... Join Date: Nov 2001 Location: Fredericksburg,Va Age: 49 Posts: 907	after you remove the screws for the doot handle and the cup portion to hold on to just start at the very bottom and pul out a little and look up to see where the pops are...Oce you do put your hands on each side and pull outwards..that should pop them w/out messing them up. and if nothing else as stated go to the junkyard and pick up a coupl e extras.. __________________ Another good forum site: Tuners Alliance

04-14-2002, 04:44 PM	#7
KwikR6 Mind Blowing Join Date: Oct 2001 Location: Cloud 69 Age: 44 Posts: 8,871	Yeah dealers are a rip off...but they do have them at least __________________ I JDM. I My Honda The epitome of stupidity is expressed so fluidly with the shity lyric theory you try to spit at me. I CAN'T WAIT FOR SUMMER!!!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-13-2002, 06:39 PM	#2
slowEJ6 Registered User Join Date: Nov 2001 Location: Oviedo, FL Age: 42 Posts: 3,195	unscrew the door handle, unscrew anything from the door armrest, unscrew the speaker, unscrew any screws around the speaker area, look for screws under the door......pry stupid little caps off, yank the panel off. that should do it.

04-13-2002, 06:49 PM	#3
seanjuan Posts: n/a	i pretty much figured this is how it was done i'm just a bit nervous about the prying off of stupid little white caps. i agree that those things suck because i always seem to break them and then they don't go back on very well oh well..... here's to nothing

04-14-2002, 03:34 PM	#6
seanjuan Posts: n/a	so let's say i break a piece and go to the junkyard to find out that i can't find a replacement.... is there anywhere you can order these, like a dealer or something? a dealer would probably charge me 20 for them, F***in dealers! later