.:HSTuners::


::Hondas Wanted::
 

Go Back   HSTuners > Honda / Acura Cars > Accord
User Name
Password
FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
Old 09-09-2001, 02:00 AM   #1
94_AcCoRd_EX
Insomniac Moderator
 
94_AcCoRd_EX's Avatar
 
Join Date: Aug 2001
Location: OR
Age: 43
Posts: 11,142
Making a true short shifter

Hey guys, I was just thinking about something, and I wanted your input. I already have a B&M short shift adapter, but it doesn't reduce the throw that much, though I like it.

Has anyone actually taken the stick out, cut out a 1 inch or so piece from the bottom section, and re-welded it? I have heard speculation that this would work, but would it? Just want some opinions.

Thanks guys... and ladies :p
94_AcCoRd_EX is offline   Reply With Quote
Old 09-09-2001, 03:12 AM   #2
azn_nite_ryder
 
Posts: n/a
yes it does work.. i have the b and m adapter too... and cut it 1.5" and it works wonders.... well at least im happy with it....
  Reply With Quote
Old 09-09-2001, 12:18 PM   #3
94_AcCoRd_EX
Insomniac Moderator
 
94_AcCoRd_EX's Avatar
 
Join Date: Aug 2001
Location: OR
Age: 43
Posts: 11,142
Thanks azn_nite_ryder, that sounds good. So you cut it out of the bottom section (I think that's the only place to do it)? Is there anything special required to do it? I don't have the tools to weld it, so I'm going to have to get it done.

Thanks again azn_nite_ryder.
94_AcCoRd_EX is offline   Reply With Quote
Old 09-09-2001, 11:35 PM   #4
azn_nite_ryder
 
Posts: n/a
hmmm.. you know what... i think they cut the top... no welding.... but dont quote me on that.... i'll check on what they did and i'll get back to ya....

No pRobs
  Reply With Quote
Old 09-09-2001, 11:50 PM   #5
jweller
 
Posts: n/a
rather than weld it, why not use a tap and die set to add threads to the unthreaded portion of the lever, and then cut off what you want. A lot easier than removing the shift lever from the car to weld it.
  Reply With Quote
Old 09-10-2001, 01:33 AM   #6
94_AcCoRd_EX
Insomniac Moderator
 
94_AcCoRd_EX's Avatar
 
Join Date: Aug 2001
Location: OR
Age: 43
Posts: 11,142
jweller, my only concern was that the stick gets thick and curves not too far from the top. I haven't measured exactly, but I'm not sure there is enough room. Right now I'm using a momo knob, so the threads aren't that important to me.

I was thinking of going to a junkyard and getting an extra stick to experiment on.
94_AcCoRd_EX is offline   Reply With Quote
Old 09-28-2001, 05:59 PM   #7
94_AcCoRd_EX
Insomniac Moderator
 
94_AcCoRd_EX's Avatar
 
Join Date: Aug 2001
Location: OR
Age: 43
Posts: 11,142
Now that we have some more people around... anyone else have suggestions? I haven't had the time to work on it yet.
94_AcCoRd_EX is offline   Reply With Quote
Old 10-17-2001, 11:18 AM   #8
Racing Rice
Project Combat Honda
 
Racing Rice's Avatar
 
Join Date: Sep 2001
Location: Highland,OH
Age: 45
Posts: 7,985
Quote:
Originally posted by jweller
rather than weld it, why not use a tap and die set to add threads to the unthreaded portion of the lever, and then cut off what you want. A lot easier than removing the shift lever from the car to weld it.

This is the way Ive always heard of it being done.. I dont know about an accord but the bend on the civic doesnt start until much lower..
__________________
Racing Rice
Racing Rice is offline   Reply With Quote
Old 10-18-2001, 01:20 AM   #9
94_AcCoRd_EX
Insomniac Moderator
 
94_AcCoRd_EX's Avatar
 
Join Date: Aug 2001
Location: OR
Age: 43
Posts: 11,142
Thanks for the info. I've never used a tap and die set, anyone want to shed some light on the subject? How much do they cost? Also, does anyone know what size to buy?

And I'm off to bed... gotta get up early and take a dynamics midterm :: college is way too hard
__________________
1994 Accord EX coupe

--Need hosting for your pics on HST? PM me...--
94_AcCoRd_EX is offline   Reply With Quote
Old 10-19-2001, 02:54 PM   #10
ChrisCantSkate
Thought Police
 
ChrisCantSkate's Avatar
 
Join Date: Aug 2001
Location: orlando florida
Age: 40
Posts: 9,662
i know this is how we do it on preludes:
cut the desided amount, then use the aftermarket shift knobs that slide over the shifter to just hold on, also if you wana keep the shifter on and do it in your car, use a dremal and cut the bottom off a milk gallon jug, and put it over the shifter upside down to catch all the shavings when you cut it w/ the dremal. i imagine that accords would be the same way.
__________________
Black Vtec Prelude-h22a power'd



Many dreams come true, and some have silver linings.
I live for my dreams and a pocket full of gold.
ChrisCantSkate is offline   Reply With Quote
Old 10-19-2001, 10:32 PM   #11
94_AcCoRd_EX
Insomniac Moderator
 
94_AcCoRd_EX's Avatar
 
Join Date: Aug 2001
Location: OR
Age: 43
Posts: 11,142
Well, I actually do have a Momo knob with set screws. It hardly stays on now, the screws back out even with locktite, so I didn't think it would stay on a smooth shaft. So there are no problems doing it like that? Cool, I'll try it when I get the time.
__________________
1994 Accord EX coupe

--Need hosting for your pics on HST? PM me...--
94_AcCoRd_EX is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 11:13 AM.


Powered by vBulletin Version 3.5.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
© 2006 HSTuners.com