.:HSTuners::

05-28-2003, 10:23 AM

Does anybody have a recipe for removing tint. The people that owned the car before me obviously tried to clean the back window with an amonia based cleaner and they screwed up the tint. I've tried to get it off using almost everything, but i still can't. Anybody have some tips.

05-28-2003, 11:19 AM

heres what you need:

http://www.tintdude.com/remove.html

05-28-2003, 12:39 PM

thx man, can't get the link to work right nwo but it's probably my crappy comp lol.

pimpinprelude · 05-29-2003, 10:35 PM

""To over come separation between layers you must soften the adhesive so that both layers peel at the same time. This is very important, if you peel the just the top layer, you may as well just use razor blades as there is no way to peel the second layer off without picking at it for a few hours. You MUST try to peel both layers at once.

NOTE: You are more than likely to damage one or more of your defroster lines, when this happens, the cut line will not work anymore. Some cars have radio antennas mounted alongside the defrosters made of the same material. If you damage these, your radio antenna will not work! Be careful! Taking it to a tint shop to be done greatly increases the odds of saving the lines, but even a tint shop can not promise to save your lines, sometimes the film is just to far gone.

Step 2:
First, clear the window of any obstructions, like the brake light, speaker covers etc.

Step 3:
Next cut open the garbage bag so that it will be big enough to cover the entire window. Spray some water on the outside of the back window and the lay plastic bag over the glass. Cut away excess plastic so that it is now roughly the same shape as the glass.

Step 4:
Next, lay a tarp over rear deck and seat, spray ammonia liberally on the inside of the back window. (Ammonia is very strong, I suggest you hold your breath during this step) and cover ammonia soaked tint with the plastic bag so that it won't evaporate.

Step 5:
Park the car with rear window facing the sun for about an hour. The film should now be ready to peel.

Step 6:
When you are ready to start peeling, leave the plastic in place so the ammonia wont dry. Get the peeling started with a razor blade in a corner where there are no defroster lines. Try to peel film off in one piece. If the ammonia dries as you peel, the glue will get hard again, so spray a bit of ammonia on the area as you peel.

Step 7:
Once the film is peeled you will need to scrub the adhesive off with ammonia and fine 0000 steel wool.

Mop up scrubbed areas with paper towels before they dry. Finish up with window cleaner and paper towels.

Removing tint from side windows
Soaking is not nessesary here. You may want to use a simple razorblade holder. Cut a notch onto the upper area of the film so that you have a piece to pull. Try to peel the film, it will probably come off in two or three pieces.
Spray the remaining adhesive with soapy water, and scrape the adhesive off with a razor blade, avoiding the edges of the glass until last to keep the blade sharp. You may need to use a few blades as they dull quickly. Finish up with window cleaner and paper towels. Inspect for missed glue (its clear and hard to see)""

there u go bro.... i know it sucks to have a crapy comp...

05-28-2003, 10:23 AM	#1
93Honda Posts: n/a	Removing Tint Does anybody have a recipe for removing tint. The people that owned the car before me obviously tried to clean the back window with an amonia based cleaner and they screwed up the tint. I've tried to get it off using almost everything, but i still can't. Anybody have some tips.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-28-2003, 11:19 AM	#2
Mischief(LTS) Posts: n/a	heres what you need: http://www.tintdude.com/remove.html

05-28-2003, 12:39 PM	#3
93Honda Posts: n/a	thx man, can't get the link to work right nwo but it's probably my crappy comp lol.

05-29-2003, 10:35 PM	#4
pimpinprelude Registered User Join Date: Mar 2003 Location: Atlanta Age: 36 Posts: 1,325	""To over come separation between layers you must soften the adhesive so that both layers peel at the same time. This is very important, if you peel the just the top layer, you may as well just use razor blades as there is no way to peel the second layer off without picking at it for a few hours. You MUST try to peel both layers at once. NOTE: You are more than likely to damage one or more of your defroster lines, when this happens, the cut line will not work anymore. Some cars have radio antennas mounted alongside the defrosters made of the same material. If you damage these, your radio antenna will not work! Be careful! Taking it to a tint shop to be done greatly increases the odds of saving the lines, but even a tint shop can not promise to save your lines, sometimes the film is just to far gone. Step 2: First, clear the window of any obstructions, like the brake light, speaker covers etc. Step 3: Next cut open the garbage bag so that it will be big enough to cover the entire window. Spray some water on the outside of the back window and the lay plastic bag over the glass. Cut away excess plastic so that it is now roughly the same shape as the glass. Step 4: Next, lay a tarp over rear deck and seat, spray ammonia liberally on the inside of the back window. (Ammonia is very strong, I suggest you hold your breath during this step) and cover ammonia soaked tint with the plastic bag so that it won't evaporate. Step 5: Park the car with rear window facing the sun for about an hour. The film should now be ready to peel. Step 6: When you are ready to start peeling, leave the plastic in place so the ammonia wont dry. Get the peeling started with a razor blade in a corner where there are no defroster lines. Try to peel film off in one piece. If the ammonia dries as you peel, the glue will get hard again, so spray a bit of ammonia on the area as you peel. Step 7: Once the film is peeled you will need to scrub the adhesive off with ammonia and fine 0000 steel wool. Mop up scrubbed areas with paper towels before they dry. Finish up with window cleaner and paper towels. Removing tint from side windows Soaking is not nessesary here. You may want to use a simple razorblade holder. Cut a notch onto the upper area of the film so that you have a piece to pull. Try to peel the film, it will probably come off in two or three pieces. Spray the remaining adhesive with soapy water, and scrape the adhesive off with a razor blade, avoiding the edges of the glass until last to keep the blade sharp. You may need to use a few blades as they dull quickly. Finish up with window cleaner and paper towels. Inspect for missed glue (its clear and hard to see)"" there u go bro.... i know it sucks to have a crapy comp...