.:HSTuners::

FullSink18 · 04-24-2004, 06:33 PM

Hey everybody,
I was wondering if anybody had a picture of an installed rear lower tie bar, if so would you post that pic. I am trying to get an idea of where exactly this gets bolted into. Thanks

ebpda9 · 04-25-2004, 01:21 AM

i hope this helps. it's a 92 but thwe cb7 and dc5/7 chassis are almost the same

FullSink18 · 04-26-2004, 01:44 PM

Thanks a ton. I was pretty sure that was where it was supposed to go, just needed to make sure.

05-16-2004, 07:41 PM

Hondaman,

In that picture, what sway bar is that back there? Is it an ST bar? Any problems with the mount points breaking away? Do you have a matched front bar, too?

ebpda9 · 05-16-2004, 08:18 PM

i have only the rear bar. the front one is the stock 22mm. i haven't had any problems with mounting points braking so far and a 3" drop

04-24-2004, 06:33 PM	#1
FullSink18 1st Gear Join Date: Apr 2003 Location: Patton, PA Age: 39 Posts: 57	Rear Lower Tie Bar Hey everybody, I was wondering if anybody had a picture of an installed rear lower tie bar, if so would you post that pic. I am trying to get an idea of where exactly this gets bolted into. Thanks __________________ Mods on Car include: --------------------------- Halo lights - Altezza taillights Clear bumper - Corner - Side lights Mesh grill Air intake - Obx b5 bomb muffler powertech headers Alpine head deck Audiobahn Subs/amps/speakers race pedals - Inside neons short shifter -glo guages front and rear strut bars (APC) Full custom painted interior back seat reupholstered in vinly Ground Control coilovers tokico HP struts Stage 2 racing clutch APC Race seats Mugen racing harnesses AeroSpeed quick clutch

04-25-2004, 01:21 AM	#2
ebpda9 Repost Wagon Join Date: Dec 2001 Location: over here Age: 43 Posts: 17,266	i hope this helps. it's a 92 but thwe cb7 and dc5/7 chassis are almost the same __________________

04-26-2004, 01:44 PM	#3
FullSink18 1st Gear Join Date: Apr 2003 Location: Patton, PA Age: 39 Posts: 57	Thanks a ton. I was pretty sure that was where it was supposed to go, just needed to make sure. __________________ Mods on Car include: --------------------------- Halo lights - Altezza taillights Clear bumper - Corner - Side lights Mesh grill Air intake - Obx b5 bomb muffler powertech headers Alpine head deck Audiobahn Subs/amps/speakers race pedals - Inside neons short shifter -glo guages front and rear strut bars (APC) Full custom painted interior back seat reupholstered in vinly Ground Control coilovers tokico HP struts Stage 2 racing clutch APC Race seats Mugen racing harnesses AeroSpeed quick clutch

05-16-2004, 08:18 PM	#5
ebpda9 Repost Wagon Join Date: Dec 2001 Location: over here Age: 43 Posts: 17,266	i have only the rear bar. the front one is the stock 22mm. i haven't had any problems with mounting points braking so far and a 3" drop __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-16-2004, 07:41 PM	#4
Eric91Z Posts: n/a	Hondaman, In that picture, what sway bar is that back there? Is it an ST bar? Any problems with the mount points breaking away? Do you have a matched front bar, too?