.:HSTuners::

01-28-2002, 09:22 PM

I just swapped my catalytic converter wit my friend's and got a new header and when i did my check engine light went on i checked all my o2 sensors (including the one on my cat and they were all tightened right...anyone know how to turn off my check engne light??or reset my ecu?

*BlackDeuceCoupe* · 01-28-2002, 10:38 PM

I just disconnect my battery cables for about 30 minutes, then reattach the cables. When I start my motor, I don't touch the throttle for 5 minutes or so. I use that time to reset my radio stations. That's about it...

01-28-2002, 10:45 PM

also......sometimes if the check engine light comes on, you need to drive the car on "three trips" is what they recommend....that means you have to start the car.....drive it.........shut it off.....and then do it again multiple times.....it should go out after that

01-28-2002, 11:04 PM

pull the ecu fuse (15a) and the back up fuse (7.5a), wait 15 sec, reinstall the fuses, and your're done. if the MIL is gone, wait for like 5 min or so and dont step on the gas. after that, shut the engine off..this resets the memory of the ecu to maximize the mixture of gas and air. if MIL is still on, you might want to check the code it's throwing...

Racing Rice · 01-29-2002, 09:31 AM

Quote:

Originally posted by SWIFT
pull the ecu fuse (15a) and the back up fuse (7.5a), wait 15 sec, reinstall the fuses, and your're done. if the MIL is gone, wait for like 5 min or so and dont step on the gas. after that, shut the engine off..this resets the memory of the ecu to maximize the mixture of gas and air. if MIL is still on, you might want to check the code it's throwing...

This is the way I do it also... If you need to know how to check the code look in the Step By Step forum, I put instructions out there.

*KwikR6* · 01-30-2002, 12:16 AM

Quote:

Originally posted by BlackDeuceCoupe
I just disconnect my battery cables for about 30 minutes, then reattach the cables. When I start my motor, I don't touch the throttle for 5 minutes or so. I use that time to reset my radio stations. That's about it...

that's what we did when we did my friends intake on his 98
werked fine

01-28-2002, 09:22 PM	#1
QwikSiLvErCIVIC Posts: n/a	O2 sensor help I just swapped my catalytic converter wit my friend's and got a new header and when i did my check engine light went on i checked all my o2 sensors (including the one on my cat and they were all tightened right...anyone know how to turn off my check engne light??or reset my ecu?

01-28-2002, 10:38 PM	#2
BlackDeuceCoupe The Great Ape Join Date: Sep 2001 Location: Skull Island Posts: 774	I just disconnect my battery cables for about 30 minutes, then reattach the cables. When I start my motor, I don't touch the throttle for 5 minutes or so. I use that time to reset my radio stations. That's about it... __________________ Posted by BlackDeuceCoupe - 2oo0 Honda CiViC FBP HX cOUPe "Pay special attention to posts by BlackDeuceCoupe, the instigator of the forum, who does a nice job of breaking my column and responses down." - Paul Brink, ASU State Press DISCLAIMER The existence of BDC is disputable. The existence of views, in the absence of anyone to hold them is problematic. The existence of the reader is left as an exercise in the second order coefficient.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-28-2002, 10:45 PM	#3
ricerroni Posts: n/a	also......sometimes if the check engine light comes on, you need to drive the car on "three trips" is what they recommend....that means you have to start the car.....drive it.........shut it off.....and then do it again multiple times.....it should go out after that

01-28-2002, 11:04 PM	#4
SWIFT Posts: n/a	pull the ecu fuse (15a) and the back up fuse (7.5a), wait 15 sec, reinstall the fuses, and your're done. if the MIL is gone, wait for like 5 min or so and dont step on the gas. after that, shut the engine off..this resets the memory of the ecu to maximize the mixture of gas and air. if MIL is still on, you might want to check the code it's throwing...