Alright...
 

Its too slow in here...so I must take responsibility and maybe help it along...

Everyone list your latest civic mod...e-, looks, power, etc, and then what your next planned mod is.

My latest was p28 obd1 conversion
The next will be gsr rear brake conversion thats sitting in the garage (need some more parts (lines,cables,prop valve new rotors+pads) :rolleyes: )

i put on my rims back in october. i got the konig mp3s (the advan knock-offs) with falken ziex 512 tires. i'm pretty happy with 'em. i don't have a really accurate gauge for it since all i had before were my miniscule 14" stockers with crap-ass tires, but it handles alot better. it's more fun taking corners now :yes:

read sig

still gotta order the Quaife and Final drive, i should have everything done by christmas.

hmm i don't drive a civic but i will post here:

rebuilt f22 and a custom turbo
rear disk conversion (sitting at my friends house)
paint job
fit a 94 accord ex lip on the front bumper

last mod would have been my intake, next Im hopeing to get some rims (hopefully my dads truck can be found soon as it was stolen early this morning and what gets most of us is there were tons of other vehicles around that are a butt load better all together then his truck so I can get rid of my old car to get the $ for them little sooner)

working on the GSR swap its gonna be done hopefully soon waiting on mounts for thurs and conversion harness on thurs then ill have a GSr motor ACT clutch flywheel- Apexi Header and Apexi N1 cat back < i just got my car back got a Kamanari Hood and a Cwest bumper and jdm headlights... whats next who knows>?

actual jdm headlights?
did you splurge for the ctr lamps?

hmm my last mod was 96Si spoiler prepainted to match. still uninstalled till after winter. Red/Clear Tail Lights, HyperWhite 7000K Bulbs, EX Conversion almost completed.

Soon to buy:CF Hood, Rims:undecided on which to get.,New Stock Front Bumper.

Last mod, car wash.

J/k - Engine swap.

Next mods -> Tokico Illumina's or Koni Yellow's (havent decided yet) some minor body work, and a new coat of red paint.

after that -> Turbo Kit.

I just had my muffler put on, it was a $18 ebay special called Dragger 2. It sounds good, nice and quiet. My next mod will depend on what I get for Christmas....front strut bar, rear strut bar, or intake....hopefully all of them!

splurge
;)

recent mod....intake

in the spring
rims, tires, coilovers and shocks

....:rolleyes:

i just realized im only modding the exterior of my car.

i need to start buying things for the engine. I will leave it stock till its more broke in. dont want to blow a new motor.

CIVIC:
Added mods:
-OBD1 conversion= p28 on the "hack"
-Skunk2 front cambet kit
-GReddy profeb-B electronic boost controller

On the way:
-ACT stage2 clutch
-dyno tune the "hack"

TEG:
Not installed, waiting to get more parts before install:
-Garrett T3T04e 57t compressor and 63 A/R turbine
-South Florida Performance race turbo manifold
-60mm GReddy A/F ratio gauge
-60mm GReddy EGT warning gauge
-60mm GReddy boost peak and hold gauge
-Tial race BOV 7psi spring
-Tial 38mm external wastegate .5 bar

greddy gauges!
$ BLING BLING $
Im plannin on those myself :)

Good stuff man. www.prostreetonline.com has GReddy gauges cheaper than any other place I've seen. I'm also getting the 52mm GReddy oil pressure gauge and the 52mm GReddy fuel pressure gauge to go next to a GReddy profec-B spec II boost controller or GReddy profec-E01 (if I get the GReddy E-manage). :yes: .............and GReddy turbo timer too, of course :D

doesnt Greddy = Trust?

if so im also planning on the same mods sort of.

Yep^

ok. well then, im going to buy all Trust gauges. so it goes with my japanese MPH guage. if that makes any sence.

Also, any pressure gauges will not read in psi.

only problem I have with the greddy gauges are the green lights...Know if the bulbs are that color of if its the gauge face's filter?
I hate teal green lights...

I have...

Chikara Header
Catco Cat
Magnaflow catback
Iceman Intake (cold air or short ram)
ES Master kit (bushings)
ES motor mount inserts
Mugen Trailing arm bushings (to be installed still)
JDM (sdm) headlights
MSD Blaster coil
MSD Modifier Cap (to use external coil)
Taylor pro wires
Integra rear disk conversion
Power stop rotors all around

*edit*
I forgot...
15" Konig Heliums (about 11lbs each)
B&M Short Shifter
*/edit*

That's about it...

I got a porsche 944 center console as my only interior mod.

I don't know that anything is on the horizon... If I start making MUCH more money or my engine blows I'll probobly get a swap (buy a totalled usdm integra and swap over engine tranny and seats.... sell off the rest).

THANKS PDIGGITY FOR NOT GIVING CREDIT TO HE WHO HOOK THEE UP WITH CHEAP P28 sExCU

My last mods were

Bronze 15" Rota RNR
AEM CAI cut to long ram
Amber corners
and SWAP woo

Planning on paint soon.

latest mod done to the car: short shifter

upcoming "mod": paint/install a new oem bumper, paint side skirts

future mod: Greddy 19T kit or suspension and rims, still undecided and currently saving up money...

Oh yes...mucho's gracias to shaved for the ultra affordable p28 (50 whole dollars)
:bow:

I would've bought it too for that price. :D

yes. *basks in glory*

latest mod> NGK plugs, NGK wires, Clear distributor cap, new rotor.

next mod> do a mini-me swap or full b20 swap

Now looking for a P28 ECU for Hondata on the Teg....